Radial X-Amp Active Re-Amplifier

$289.00 inc GST

Radial X-Amp is an active Reamper that allows the engineer to play a pre-recorded track back through guitar amplifiers and pedals. This opens the door to explore new musical sounds and spur on the creative process so that your recording stands out.

SKU: RA-X-Amp Category:

Description

Radial X-Amp is an active re-amper that allows the engineer to play a pre-recorded track back through guitar amplifiers and pedals. This opens the door to explore new musical sounds and spur on the creative process so that your recording stands out.

Radial X-Amp – Features

  • Active re-amp with two outputs
  • 100% discrete class-A signal path
  • Transformer isolated to eliminate noise
  • Variable ‘set & forget’ level control

Using the Radial X-Amp is easy: start by recording a dry track using a high quality direct box like the Radial J48. Send the new track from your recorder via the X-Amp to your guitar amps, effect pedals or combinations thereof. Once the basic track has been recorded, replacing or adding tracks can be done well after the session player has gone home. This eliminates tiresome repetition and assures a fresh vibrant performance on the final recording. Furthermore, by driving two amps at the same time, new sounds and textures can be created while allowing you to make artistic decisions as the recording progresses.

Following the critically acclaimed Radial JD7 Injector, the Radial X-Amp employs a unique class-A circuit design that has been optimized for use with guitars. Features include balanced line level input with LED peak indicator and level control, class-A circuit topology for optimal reach and frequency response, a transformer isolated output to eliminate hum and buzz caused by ground loops, a 180º polarity reverse switch to bring both amps into phase, and a dual ground lift switch for noise-free operation.

As with all Radial products, the X-Amp is built like a tank to provide years of trouble-free performance. An internal I-beam skeleton provides maximum protection against external stress which could cause solder points to fail. This is supplemented with an innovative bookend design that creates a protective zone around the switches, potentiometer and connectors. A full bottom no-slip pad performs double duty by keeping the X-Amp from sliding around when placed on a vibrating amplifier while also providing electrical and mechanical isolation. Reamping works equally well on bass, keyboards, drums and voice. Once you start Reamping, you will never record any other way.

The Radial X-Amp… the active Reamp® for professional recording engineers.

Radial X-Amp – Stage 1

To Reamp, start by recording a dry track using a Radial J48 and splitting the signal. Record the wet track using a mic so that the guitarist can hear it.
Radial X-AMP - stage 1

Radial X-Amp – Stage 2

Send the dry track back to the guitar amps and pedals using the X-Amp. Adjust the tone and move the mics around till it sounds right. You can always come back and Reamp later.
Radial X-AMP - stage 2

Radial X-Amp – Other Uses

Try sending a vocal track into a Marshall amp or a Tonebone Classic to add tube warmth and grit. Take it a step further by sending your kick drum to a wah pedal. There are no limits!
Radial X-AMP - other uses

Radial X-Amp Active Re-Amplifier was last modified: January 30th, 2016 by Doug Watt

Additional information

Brand

Radial

Unit of Measure

each

Specifications

Specifications  
Specifications are subject to change without notice.
Audio circuit type: 100% discrete class-A
Frequency response: 20Hz ~ 15kHz (± 1.0dB)
Signal to noise ratio: 88dB below instrument level (-20dBu)
Dynamic range: 119dB
Noise floor: OUT-1 -110dB; OUT-2 -108dBu
Maximum input: +22dBu
Total harmonic distortion: 0.02% @ -15dBu
Inter-modulation distortion: 0.02% @ -20dBu
Input impedance: 600Ω
Features  
XLR input: Balanced line-level, AES standard (pin-2 hot)
Ground lift (input): Disconnects pin-1 at the XLR input
Output level: Adjustable
Output type: Out-1 direct, Out-2 isolated
Polarity: 180º polarity reverse on output-2
General  
Power: +15VDC/400mA adapter included
Construction: 14 gauge steel chassis & outer shell
Finish: Durable powder coat
Size: 3.3″ x 5.0″ x 2″ (84 x 127 x 48mm)
Weight: 1.55lb (720g)
Shipping size: 5" x 2.75" x 10.75" (127 x 70 x 273mm)
Shipping weight: 2.6lb (1.18kg)
Conditions: For use in dry locations only between 5°C and 40°C
Warranty: Radial 3-year, transferable
Radial X-Amp Active Re-Amplifier was last modified: January 30th, 2016 by Doug Watt

Product Enquiry